This N-number isn't registered right now. Below is its last known registration, canceled Jul 20, 2018.
Safety record in brief:1 NTSB accident (substantial damage, Jul 2017)6 ADs may apply1 service difficulty report
We never show street addresses, even though they appear in the public FAA file. Individual owners are shown by city and state only.
Total time and engine hours aren't public. They appear here once the owner adds logbooks.
Individual owners are shown by city and state only.
The student pilot's mismanagement of the main rotor rpm, which resulted in low rotor rpm, a high descent rate, and a subsequent hard landing.
From NTSB records; matched by serial number.Read NTSB report (search CAROL for WPR17LA158)
These match the airframe or engine model. Whether each one applies, and whether it's been complied with, depends on serial numbers, equipment and logbook entries. Applicability must be confirmed by a mechanic against the aircraft's records.
| AD | Subject | Effective | Applies to |
|---|---|---|---|
| 2018-02-01 | The Enstrom Helicopter Corporation Helicopters | Feb 21, 2018 | Airframe (F-28C)Certain serial numbers: 480 5001–5006. Only with: With main rotor spindle P/N 28-14282-11 or 28-14282-13 installed. |
| 2017-26-03 | The Enstrom Helicopter Corporation Helicopters | Jan 4, 2018 | Airframe (F-28C)Only with: Rod end bearing assembly P/N 01-824-08E-011, 09455-01-824-08E-011, ECD091-1, ASMK8T, M81935/1-08K, MS21242S8K, or MTK8 installed. |
| 2012-11-05 | Enstrom Helicopter Corporation Helicopters | Jul 3, 2012 | Airframe (F-28C)Only with: Helicopters with trim relay P/N KUP14D55-24, KUP14D55-472, M83536/10-015M, or M83536/10-024M installed; does not apply to helicopters with reversible trim motor P/N 28-16621 or P/N AD1R-10. |
| 2011-26-10 | Enstrom Helicopter Corporation Helicopters | Jan 23, 2012 | Airframe (F-28C)Only with: Helicopters with a trim relay P/N KUP14D55-472, M83536/10-015M, or M83536/10-024M installed; does not apply to helicopters with reversible trim motor P/N 28-16621 or AD1R-10. |
| 2002-08-03 | Enstrom Helicopter Corporation Model F-28, F-28A, F-28C, F-28F, 280, 280C, 280F, and… | May 2, 2002 | Airframe (F-28C) |
| AD | Subject | Effective | Applies to |
|---|---|---|---|
| 96-06-03 | The Enstrom Helicopter Corporation Model F-28, F-28A, F-28C, F-28C-2, F-28F, 280, 280C… | Mar 19, 1996 | Airframe (F-28C) |
AI-extracted — verify against original. Matched from each AD's applicability section; ADs replaced by a later AD are left out.
Reports of failures and defects that operators and repair stations sent to the FAA since 1995. A report describes one finding; it is not an accident.
THE NR 3 ROD CAP SEPARATED FROM ROD. ROD BOLTS WERE DAMAGED TOO BADLY TO BE IDENTIFIED FOR SURE, BUT SHOULD BE PART NUMBER LISTED. THESE BOLTS HAVE STRETCH TORQUE. SUBMITTER SUSPECTS IMPROPER TORQUING (EITHER TOO MUCH OR NOT ENOUGH) CAUSING BOLT FAILURE. AD 95-07-1 DOES NOT APPLY.
From FAA Service Difficulty Reports; matched by N-number and serial number.