This N-number isn't registered right now. Below is its last known registration, canceled Mar 24, 2023.
Safety record in brief:2 NTSB accidents (substantial damage at worst, latest May 2021)6 ADs may apply1 service difficulty report
We never show street addresses, even though they appear in the public FAA file. Individual owners are shown by city and state only.
Total time and engine hours aren't public. They appear here once the owner adds logbooks.
Individual owners are shown by city and state only.
A loss of drive to the rotor system due to the disengagement of the main belt drive tensioning system, which resulted in a forced landing. The disengagement was due to inadequate clearance between the clutch handle and the roll pin in the handle bellcrank when the handle was in the stowed position.
From NTSB records; matched by serial number.Read NTSB report (search CAROL for ANC21LA038)
A LOSS OF ENGINE POWER AS A RESULT OF THE STUDENT PILOT INADVERTENTLY PULLING THE MIXTURE CONTROL TO THE IDLE CUT-OFF POSITION, AND THE FLIGHT INSTRUCTOR'S INADEQUATE SUPERVISION. A CONTRIBUTING FACTOR TO THE ACCIDENT WAS THE ROUGH AND UNEVEN TERRAIN.
From NTSB records; matched by serial number.Read NTSB report (search CAROL for BFO90LA011)
These match the airframe or engine model. Whether each one applies, and whether it's been complied with, depends on serial numbers, equipment and logbook entries. Applicability must be confirmed by a mechanic against the aircraft's records.
| AD | Subject | Effective | Applies to |
|---|---|---|---|
| 2018-02-01 | The Enstrom Helicopter Corporation Helicopters | Feb 21, 2018 | Airframe (F-28F)Certain serial numbers: 480 5001–5006. Only with: With main rotor spindle P/N 28-14282-11 or 28-14282-13 installed. |
| 2017-26-03 | The Enstrom Helicopter Corporation Helicopters | Jan 4, 2018 | Airframe (F-28F)Only with: Rod end bearing assembly P/N 01-824-08E-011, 09455-01-824-08E-011, ECD091-1, ASMK8T, M81935/1-08K, MS21242S8K, or MTK8 installed. |
| 2012-11-05 | Enstrom Helicopter Corporation Helicopters | Jul 3, 2012 | Airframe (F-28F)Only with: Helicopters with trim relay P/N KUP14D55-24, KUP14D55-472, M83536/10-015M, or M83536/10-024M installed; does not apply to helicopters with reversible trim motor P/N 28-16621 or P/N AD1R-10. |
| 2011-26-10 | Enstrom Helicopter Corporation Helicopters | Jan 23, 2012 | Airframe (F-28F)Only with: Helicopters with a trim relay P/N KUP14D55-472, M83536/10-015M, or M83536/10-024M installed; does not apply to helicopters with reversible trim motor P/N 28-16621 or AD1R-10. |
| 2002-08-03 | Enstrom Helicopter Corporation Model F-28, F-28A, F-28C, F-28F, 280, 280C, 280F, and… | May 2, 2002 | Airframe (F-28F) |
| AD | Subject | Effective | Applies to |
|---|---|---|---|
| 96-06-03 | The Enstrom Helicopter Corporation Model F-28, F-28A, F-28C, F-28C-2, F-28F, 280, 280C… | Mar 19, 1996 | Airframe (F-28F) |
AI-extracted — verify against original. Matched from each AD's applicability section; ADs replaced by a later AD are left out.
Reports of failures and defects that operators and repair stations sent to the FAA since 1995. A report describes one finding; it is not an accident.
INFORMATION APPLICABLE TO MODELS, F28C, F28C-2 F28-F, 280F, 280FX. INSPECTION FOUND TAIL ROTOR CABLES FRAYED WHERE THEY PASS OVER THE AFT ALIGNMENT PULLEYS IN THE TAIL CONE. PULLEYS WERE LUBED, FREE AND TURNING. SUSPECT VIBRATION WAS CAUSING CABLES TO RATTLE IN PULLEY AND GUIDE, FATIGUING THE…
From FAA Service Difficulty Reports; matched by N-number and serial number.